I do have an option for you, but we do not recommend using lift blocks on trailers due to movement/damage they can cause overtime in trailer suspension.
Instead since you already have the spring over the axle I recommend using the Correct Track # RR23QX which will allow you to raise your trailer by either 1-1/4" or 2-1/4", and are easy to install as they just bolt on to your existing hangers. view full answer...
The bearing difference doesn't mean too much since the spindles are the same so regardless of which axle you decide to put the brake kit on you'll need a 6k rated disc brake kit with an 6 lug bolt pattern. So for that we have the Kodiak brake kit part # K2HR526D which is a fit for your spindles.
This kit does require the bearings part number # 25580 and # 15123 and seal part # RG06-070 which are sold separately.
Or if instead you were wanting a kit that uses an idler hub and a slip-on... view full answer...
As long as your existing landing gear have their weld stops in the standard positions as shown in the linked photo (15-1/2 inside to inside and 17-1/2 outside to outside) and the outer tube length matches then the Ultra-Fab 12K dual motor landing gear set # UF17-943010 will install easily in its place in the existing hangers. But if not the Ultra-Fab includes new hangers that you can weld to your frame. This jack system's high 12K capacity and independent motor control will make leveling... view full answer...
The Gen-Y Hitch Aluminum Loading Ramp Set - 144" Long x 15" Wide - 8,000 lbs, part # GH54FR, is the best option we have for you to load your smart car on a trailer that is 48" high. Unfortunately, we do not offer a version of this ramp that folds.
The longest folding aluminum ramp we offer is the Arched Loading Ramp Set - Center Fold - Aluminum - 90" x 18" - 3K, part # 288-07432-2. This set of ramps has a weight limit of 3,000 lbs. These ramps would have to be at a very steep angle to... view full answer...
We have not yet test fit the Lippert Components High-Speed Power Stabilizer Jack part # LC298707 on a 2018 Dutchmen Endurance 3556 therefore, in order to determine fit you will need to measure the distance between the two frame rails on center. They will need to be 68-11/16" apart or close in order for this system to work for you. If they are not then the only option we have is the Ultra-Fab Power Twin II Electric Stabilizer part # UF39-941705 which will fit trailers with frame rails between... view full answer...
We don't offer a block type lift, but we do offer some options that would increase your trailer's ride height.
If your 2018 Dutchmen Voltage Triton 3551 Toy Hauler has 7K rated axles, and the leaf springs are currently mounted under the axles, you can use an over/under kit like # K71-385-00 to relocate the leaf springs to the top of the axle. This will gain you the 3 inch diameter of the axle beam plus the thickness of the spring pack as a height increase.
The other option, although it... view full answer...
For your bike rack needs I recommend the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount Item # HLY64FR. For the trailer hitch I recommend the Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2" Item # C13701. We also offer bigger trailer hitch receivers if your frame is bigger than 51" like # C13704 which goes up to 66". view full answer...
If the landing gear on your 2018 Dutchman Endurance 3556 toy hauler is branded as a Lippert, Venture, Stromberg, or LCI the Lippert Components HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308 that you referenced is a confirmed fit as an upgrade replacement with more capacity. It sounds like your current motor is bad and is wanting to draw too much amperage which is why you are hearing it click like you are. view full answer...
Go To Results